Editing Harley-Davidson Flathead
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.
| Latest revision | Your text | ||
| Line 4: | Line 4: | ||
==Advantages== | ==Advantages== | ||
Generally the flathead's valves are carried on one side of the cylinder. A chamber is recessed into the underside of the head to allow the poppet valves to alternately rise from their seats to admit the fuel-air mixture and for the exhaust gases to escape the | Generally the flathead's valves are carried on one side of the cylinder. A chamber is recessed into the underside of the head to allow the poppet valves to alternately rise from their seats to admit the fuel-air mixture and for the exhaust gases to escape the combustion chamber. This has a number of advantages, primarily making the cylinder head much simpler, without the complex mechanism contained within the head of an overhead valve engine. The head of a flathead engine commonly consists of only a single piece of cast metal. | ||
It also means a valve can be operated by pushing directly up on it, as opposed to needing some sort of mechanical arrangement to push it down or to drive overhead cams, as on a [[overhead valve|"valve-in-head"]] engine. It may also lead to slightly easier cooling, as the valves ([[pushrods]] are very seldom used, Indian motorcycles are an example) are out of the way of the cylinder, making a cooling jacket simpler to construct. (See limitation below.) The line of intakes along the side of the engine leads to the alternate name '''L-block''' (or '''L-head'''), due to the cylinders having the shape of an upside-down L. This configuration is also known as (Ford) sidevalve engine. | It also means a valve can be operated by pushing directly up on it, as opposed to needing some sort of mechanical arrangement to push it down or to drive overhead cams, as on a [[overhead valve|"valve-in-head"]] engine. It may also lead to slightly easier cooling, as the valves ([[pushrods]] are very seldom used, Indian motorcycles are an example) are out of the way of the cylinder, making a cooling jacket simpler to construct. (See limitation below.) The line of intakes along the side of the engine leads to the alternate name '''L-block''' (or '''L-head'''), due to the cylinders having the shape of an upside-down L. This configuration is also known as (Ford) sidevalve engine. | ||
| Line 11: | Line 11: | ||
On the downside, the flathead also requires the airflow to make at least a 90-degree turn to enter the cylinder, which makes it less efficient, colloquially called poorer "breathing". Breathing was not greatly important for early production cars because engines could not run long and reliably at high speed, and most engines had poor combustion, so this was a minor concern given the benefits in simplicity. The maximum compression ratio is also low at only about 7:1, further reducing efficiency (although it means the engine can run on low-octane fuel). | On the downside, the flathead also requires the airflow to make at least a 90-degree turn to enter the cylinder, which makes it less efficient, colloquially called poorer "breathing". Breathing was not greatly important for early production cars because engines could not run long and reliably at high speed, and most engines had poor combustion, so this was a minor concern given the benefits in simplicity. The maximum compression ratio is also low at only about 7:1, further reducing efficiency (although it means the engine can run on low-octane fuel). | ||
The greatest advancements to flathead engine technology were developed in the 1920s through experimentation by Sir Harry Ricardo of Great Britain, who improved the performance and efficiency of flathead engines by intently studying their flow characteristics. He published his findings, and obtained patents, in 1927. Primarily, his '''Ricardo Head''' can be recognized on sight, because he moved the location of the exhaust valve farther from the center of the cylinder than the intake valve (they had previously been symmetrical). He also paid careful attention to the form of the intake and exhaust tracts cast into the cylinder block as regarded turbulence in the intake stream and within the | The greatest advancements to flathead engine technology were developed in the 1920s through experimentation by Sir Harry Ricardo of Great Britain, who improved the performance and efficiency of flathead engines by intently studying their flow characteristics. He published his findings, and obtained patents, in 1927. Primarily, his '''Ricardo Head''' can be recognized on sight, because he moved the location of the exhaust valve farther from the center of the cylinder than the intake valve (they had previously been symmetrical). He also paid careful attention to the form of the intake and exhaust tracts cast into the cylinder block as regarded turbulence in the intake stream and within the combustion chamber. | ||
A more serious concern is exhaust, which often follows a more complicated path to leave the engine. This increases the tendency for the engine to overheat under sustained heavy use. It is sometimes possible to arrange the sidevalve engine layout so that the exhaust will be taken away through a valve and an exhaust tract located on the opposite side of the cylinder from the intake valve, in which case the layout is referred to as a '''T-block''' or '''T-head'''. American LaFrance famously powered their production fire engines with T-head motors from the 1920s to the 1950s. The [[Cleveland|Cleveland Motorcycle Company]] produced a four cylinder in-line motorcycle using the T-head configuration in the 1920s. | A more serious concern is exhaust, which often follows a more complicated path to leave the engine. This increases the tendency for the engine to overheat under sustained heavy use. It is sometimes possible to arrange the sidevalve engine layout so that the exhaust will be taken away through a valve and an exhaust tract located on the opposite side of the cylinder from the intake valve, in which case the layout is referred to as a '''T-block''' or '''T-head'''. American LaFrance famously powered their production fire engines with T-head motors from the 1920s to the 1950s. The [[Cleveland|Cleveland Motorcycle Company]] produced a four cylinder in-line motorcycle using the T-head configuration in the 1920s. | ||
| Line 20: | Line 20: | ||
Although flathead in-line 4 and 6 cylinder engines were frequently used for automobiles, tractors, etc., the best known flathead automotive engine is the early 20th century Ford V-8, which has both sets of valves (intake and exhaust) located on the inside of the "Vee," and which are all operated by a single [[camshaft]] located above the [[crankshaft]]. | Although flathead in-line 4 and 6 cylinder engines were frequently used for automobiles, tractors, etc., the best known flathead automotive engine is the early 20th century Ford V-8, which has both sets of valves (intake and exhaust) located on the inside of the "Vee," and which are all operated by a single [[camshaft]] located above the [[crankshaft]]. | ||
Due to cooling and efficiency problems, flathead engines fell out of favor in "high power" applications, such as aircraft engines, prior to World War I. However they lived on for some time in the automotive world and were used on the Jeep for instance. Flatheads are no longer in common use for | Due to cooling and efficiency problems, flathead engines fell out of favor in "high power" applications, such as aircraft engines, prior to World War I. However they lived on for some time in the automotive world and were used on the Jeep for instance. Flatheads are no longer in common use for [[automobile]]s, although they are still used for some small-engine applications like [[lawnmower]]s. Because of their design, the size of valves and the [[compression ratio]] are limited, which in turn reduces available power and economy. | ||
==Harley-Davidson motorcycle flathead engines== | ==Harley-Davidson motorcycle flathead engines== | ||
| Line 27: | Line 27: | ||
In 1952, the K series flatheads was introduced, selling in parallel with the W series (which was discontinued after 1952), designed to compete with British sporting motorcycles of the time, as the American motorcycle Association allowed the 750 cc sidevalves to compete against 500 cc overhead-valve bikes. The K models featured a unit construction engine and transmission case, right side foot shift and left side foot brake, and evolved from 45 cubic inch (1952 to 1953) to 55 cubic inches by a 0.75in increase in stroke length (1954 to 1956) over its five year retail market run. The K series was replaced by the overhead valve [[Harley-Davidson Sportster|Sportster]] series in the retail market in 1957. However, racing versions of the 750 cc K model, designated KR, continued to be produced in very limited numbers for some time after, winning both roadraces and dirt track events against overhead valve bikes limited to 500 cc through 1969, when the American Motorcycle Association finally decided to change the rules and make the venerable flatheads uncompetitive. The K racers were replaced first by the iron-head XR 750cc overhead valve engine, and two years later by the alloy-head XR, which continues in service in flat track racing to this day. | In 1952, the K series flatheads was introduced, selling in parallel with the W series (which was discontinued after 1952), designed to compete with British sporting motorcycles of the time, as the American motorcycle Association allowed the 750 cc sidevalves to compete against 500 cc overhead-valve bikes. The K models featured a unit construction engine and transmission case, right side foot shift and left side foot brake, and evolved from 45 cubic inch (1952 to 1953) to 55 cubic inches by a 0.75in increase in stroke length (1954 to 1956) over its five year retail market run. The K series was replaced by the overhead valve [[Harley-Davidson Sportster|Sportster]] series in the retail market in 1957. However, racing versions of the 750 cc K model, designated KR, continued to be produced in very limited numbers for some time after, winning both roadraces and dirt track events against overhead valve bikes limited to 500 cc through 1969, when the American Motorcycle Association finally decided to change the rules and make the venerable flatheads uncompetitive. The K racers were replaced first by the iron-head XR 750cc overhead valve engine, and two years later by the alloy-head XR, which continues in service in flat track racing to this day. | ||
In 1930, the 74ci VL flathead replaced the JD Big Twin, which had featured intake-over-exhaust (IoE) valve configuration. The VL had a single downtube frame and total loss oiling, culminating in an | In 1930, the 74ci VL flathead replaced the JD Big Twin, which had featured intake-over-exhaust (IoE) valve configuration. The VL had a single downtube frame and total loss oiling, culminating in an {{convert|80|cuin|cc}} version (VLH) in 1935. In 1937, that engine was redesigned to include a recirculating lubrication system, and designated the model U, and it went into the same frame and running gear configuration as the model E Knucklehead, which had originated in 1936. The U continued to be produced in varying configurations as a 74& cubic inch U & UL (1937 to 1948), and 80 cubic inch UH & ULH motor (1937 to 1941). By that time, the first year of the aluminum-head Panhead, it had been thoroughly superseded and outsold in the marketplace by the superior performance of the overhead valve model Big Twins. | ||
==See also== | ==See also== | ||