Editing Yamaha TZ250

Yamaha also chose to "beef up" the  [[main bearings|main]] and small-end crank bearings as well as a few other minor mods  . Output was up slightly from the TD3 to 51bhp @ 10,500rpm.

1976 saw the appearance of the much awaited '''TZ250C'''. The biggest news here was the new "Monoshock" chassis, with the rear shock featuring adjustable pre-load and compression damping, as well as disc brakes front and rear. Motor-wise, the factory chose to pursue ease of riding rather than outright horsepower. Revised porting comprising wider intake and [[transfer port]]s with altered angles of entry, raised compression and a new exhaust achieved this for them to a certain degree. The exhaust was mounted on new design brackets, and the clutch basket "boss" to primary driven gear attachment was improved by changing from previous model's "dog" teeth to a  female spline, this of course required the primary driven gear to be altered to utilise a male spline. The bike sold remarkably well at just £ 1,500 including a well stocked spares kit.

The "D" model of 1977 was just about identical to the previous model except for the inclusion of revised heads with angled spark plugs and new expansion chambers with silencers as standard issue. Minor changes included the side gearbox drain bolt gasket, 2 crank web halves, base gasket and the center crank bearing.  Carburetor mods including new floats, [[float chamber]] gaskets and choke systems also appeared. Peak power hopped up by 1 to 53bhp@ 10,500rpm.

 

The factory's 1978 250cc offering, the "E" was a little disappointing in that it was virtually unchanged from the previous year's offering, apart from a new chassis which had the engine sitting approx. 20mm further forward, the bike's [[swingarm ]] remained the same. The front of the engine was retained by a pair of alloy mounting plates which required an additional 20 or so bolts, nuts and washers to secure to the engine and frame. The rear lower engine mounting bolt was also lengthened by 5mm.  A TZ250E prepared by [[Kel Carruthers]] and ridden by Californian [[Kenny Roberts]] notched many wins in the 1978 World Championships.

The '''TZ250F''' heralded welcome news for Yamaha fans when it was released in 1979. A 11kg weight reduction was achieved through further changes to the frame, (despite the fact they reverted back to welded steel engine mounting brackets from the alloy ones on the "E") including a steeper rake and an alloy swingarm, as well as this the bike featured a new exhaust and mounting system, an additional o-ring (from the previous single o-ring) in the header pipe, new conrod, wider intake port and minor carburetor mods.  The primary drive gear picked up 2 teeth to match the 350's 25, the cylinder drain tube was altered. A dipstick was also introduced and the brake [[caliper]]s became cast alloy units like the 750's . Power remained the same as it had since the "D" at 53bhp @ 10,500rpm.  A new fairing adorned the machine which was pointed below the header pipes and eliminated the old aluminum belly pan, a new fuel tank and seat unit appeared, and the clutch cover was reduced in size to a pressed aluminum job (the previous models utilised a cast aluminum unit completely covering the clutch) surrounding just the rear of the clutch unit.

[[Image:1980 Yamaha TZ250G.jpg|left|thumb|1980 Yamaha TZ250G]]

 

1980's "G" model was a further departure from the "norm" of the past 3 or 4 years. But they were still just incremental type changes since Yamaha had virtually monopolized this class of racing in 1979.  New, larger diameter forks were fitted in an effort to combat the front end "patter" problem that was frustrating so many riders. Motor-wise Yamaha went all-out for peak horsepower at the expense of engine lifespan by drastically increasing the inlet timing period by removing almost 8mm from the rear of the pistons (and slightly increasing bore size) . Thie allowed for 500 rpm higher revlimit.  This mod caused real problems with piston wear, despite the factory's attempt to counteract it with the inclusion of a short supporting "tongue" protruding down from the top of the inlet port in a vain attempt to reduce piston rocking. TZ250 G's were, as a result, very expensive to maintain, requiring re-builds after every race, though no-one complained about the extra 4bhp it provided over the D/E/F models ! Yamaha also increased the width of the secondary transfers slightly this year as well as fitting powerjet carburetors.

 

The motor spun in reverse direction as the factory tried to further reduce the stress on the rear of the pistons. The crank was no longer a single unit, it was now a pair of cranks with a gear on the end to deliver the power to the gearbox. Despite the frame shedding 3kg, the overall weight was reduced by just 1kg. The steering rake was  altered and the swingarm  also lengthened to compensate for the shorter frame length of this model. The engine was now mounted slightly further towards the front of the bike. The new rear shock became fully adjustable for both compression and rebound damping as well as pre-load and the shock picked up a rear rubber mounting. The fork diameter went up by 1mm and brake wise the factory reverted back to the old cast iron [[caliper]]s which didn't bend under pressure and also didn't [[brake fade|fade]] when hot. The new ignition dropped an igniter and pulser coil, there was now just one of each and the  inner clutch hub now became a single piece unit to eliminate one reliability problem from previous years. The un-necessary neutral switch mounting disappeared

[[Image:1987-Yamaha-TZ250T-White-5648-0.jpg|left|thumb|1987 Yamaha TZ250T in White]]

[[Image:1987-Yamaha-TZ250T-White-5648-1.jpg|left|thumb|1987 Yamaha TZ250T in White]]

[[Image:1987-Yamaha-TZ250T-White-5648-2.jpg|left|thumb|1987 Yamaha TZ250T in White]]

[[Image:1987-Yamaha-TZ250T-White-5648-3.jpg|left|thumb|1987 Yamaha TZ250T in White]]

[[Image:1987-Yamaha-TZ250T-White-5648-4.jpg|left|thumb|1987 Yamaha TZ250T in White]]

File:2001-Yamaha-TZ250K1-Silver-8116-0.jpg|left|thumb|2001 Yamaha TZ250K1 in Silver

File:2001-Yamaha-TZ250K1-Silver-8116-1.jpg|left|thumb|2001 Yamaha TZ250K1 in Silver

File:2001-Yamaha-TZ250K1-Silver-8116-2.jpg|left|thumb|2001 Yamaha TZ250K1 in Silver

File:2001-Yamaha-TZ250K1-Silver-8116-3.jpg|left|thumb|2001 Yamaha TZ250K1 in Silver

File:2001-Yamaha-TZ250K1-Silver-8116-4.jpg|left|thumb|2001 Yamaha TZ250K1 in Silver

File:2001-Yamaha-TZ250K1-Silver-8116-5.jpg|left|thumb|2001 Yamaha TZ250K1 in Silver

File:2001-Yamaha-TZ250K1-Silver-8116-6.jpg|left|thumb|2001 Yamaha TZ250K1 in Silver

File:2001-Yamaha-TZ250K1-Silver-8116-7.jpg|left|thumb|2001 Yamaha TZ250K1 in Silver