BMW R51: review, history, specs

From CycleChaos
(Redirected from BMW R 51/3)
Jump to navigation Jump to search
BMW R 51
Production 1951
Class Classic
air-cooled, four-stroke, boxer twin cylinder, 2 valves per cylinder
Bore / Stroke 68.6mm x 68.6mm
Compression ratio 6.4:1
Top Speed 81 mph
Horsepower 24.0 HP (17.9 KW) @ 5800RPM
Transmission Gear box: 4-speed, manual

Final Drive: shaft

Clutch: dry, single plate
Suspension Front: telescopic fork
Rear: coil compression springs and rubber deflection stops
Brakes Front: 200mm drum
Rear: 200mm drum
Front Tire 3.5x19
Rear Tire 3.5x19
Wheelbase 55.0 inches (1397 mm)
Length 83.86 inches (2130 mm)
Width 32.01 inches (813 mm)
Weight 190.0 kg (wet)
Manuals Service Manual

The BMW R 51/3 was a air-cooled, four-stroke, boxer twin cylinder, 2 valves per cylinder Classic motorcycle produced by BMW in 1951. Claimed horsepower was 24.0 HP (17.9 KW) @ 5800 RPM.

History[edit | edit source]

The roots of BMW are carved in history as quality manufacturers of aircraft engines which began in the early part of the 20th century. Today's logo is still a representation of a spinning propeller. Following the First World War, the Peace Treaty of Versailles banned the production of such engines so BMW, who had a reputation as a quality engine building company, began to build engines on a much smaller scale. From their aircraft engine experience, BMW were quite familiar with pistons operating opposite each other so they designed a horizontally opposed two cylinder engine with the cylinders fore and aft. BMW supplied the Victoria motorcycle company with this engine.

In 1923 BMW went on their own to build their own brand of motorcycle realizing the need for quality in the marketplace. Aircraft engineer, Max Friz, designed the more commonly known transverse horizontally opposed twin cylinder engine, an engine design that BMW still uses today more than eighty years later. Within a year of the original engine design they had almost doubled the horsepower due to the introduction of overhead valves in the flat twin.

Engine[edit | edit source]

A 68.6mm bore x 68.6mm stroke result in a displacement of just 494.0 cubic centimeters.

Drive[edit | edit source]

The bike has a 4-speed, manual transmission. Power was moderated via the dry, single plate.

Chassis[edit | edit source]

It came with a 3.5x19 front tire and a 3.5x19 rear tire. Stopping was achieved via 200mm drum in the front and a 200mm drum in the rear. The front suspension was a telescopic fork while the rear was equipped with a coil compression springs and rubber deflection stops. The wheelbase was 55.0 inches (1397 mm) long.

1938[edit | edit source]

1938 BMW R51

1950[edit | edit source]

1950 BMW R51/2

R51/3[edit | edit source]

The BMW R51/3 was BMW's first modern postwar 500cc motorcycle. It used BMW's time-tested boxer engine layout and exposed driveshaft. The R51/3 succeeded and modernized the 1950 R51/2, which was essentially a prewar design that was produced after the war.

Following World War II, Germany was precluded from producing motorcycles of any sort by the Allies. When the ban was lifted, in Allied controlled Western Germany, BMW had to start from scratch. There were no plans, blueprints, or schematic drawings. Company engineers had to use surviving prewar motorcycles to create new plans. In 1948, it introduced the 250cc R24, which was essentially a pre-war R23, complete with rigid rear end.

When larger machines were permitted, BMW introduced its R51/2 in 1950, a model that was in production for only one year and that was essentially a prewar BMW produced after the war. The R51/3 was then introduced in 1951 for a production run of four years.

The 600cc R67, sister model to the R51/3 and almost identical visually, was also introduced in 1951, but it went through two revisions. The R67/2, with 2 hp more, came out one year later and was replaced in 1955 by the R67/3, which was in production through the 1956 model year.

In 1952, BMW introduced the 600cc R68. With 35hp and a compression ratio of 8.0:1, this was the first BMW production motorcycle that could reach and pass 100mph.

1954[edit | edit source]

1954 BMW R51/3 w/STEIB TR500 Sidecar
1954 BMW R51/3 w/STEIB TR500 Sidecar
1954 BMW R51/3 w/STEIB TR500 Sidecar
1954 BMW R51/3 w/STEIB TR500 Sidecar
1954 BMW R51/3 w/STEIB TR500 Sidecar
1954 BMW R51/3 w/STEIB TR500 Sidecar
1954 BMW R51/3 w/STEIB TR500 Sidecar

1951 - 1955 BMW R 51/3[edit | edit source]

1951 - 1955 BMW R 51/3 1951 - 1955 BMW R 51/3 1951 - 1955 BMW R 51/3 1951 - 1955 BMW R 51/3

The 1951 MY BMW R 51/3 has received an upgrade in the engine department, namely, the two chain-driven camshafts that were found on the R 51/2 were replaced by a single central camshaft driven by gearwheels from the crankshaft. In all other aspects, it is mainly the same machine as its predecessor.

It comes with a front telescopic fork, dual plunger shocks as a rear suspension, a drum braking system, full fenders, a large, round headlight, a single seat, a rear luggage rack, a dual exhaust system, a blacked-out steel frame, a small tail light and a dry, single plate clutch.

In Media[edit | edit source]